Precision
Epoxy Products
" Your
Complete Epoxy Source "
a division of :
Rock Art, Ltd.
"
Professionals of Epoxy Applications "
4279 Midway Drive
Douglasville, Georgia 30134
Phone : (770) 489-0340
e-mail :
mramy@netzero.net
General Epoxy Product
List
If you cannot find what you are looking for,
Give us a call
If it is Epoxy related, we can help.
Precision Epoxy / Rock Art specializes in the Epoxy
Industry and through this combined effort as Formulator / Applicator , we
have developed our systems to cater to the needs of 'Field Use'. As
conditions and climate change from job to job, so do our techniques and
formulas change to give more control and consistency assuring the best and
most permanent installations possible.
Important to understand about
true Epoxies:
There are four phases that an epoxy goes through once the Resin (Part
'A') and the Hardener (Part 'B') are properly blended at the appropriate
mix ratio.
1) Pot Life
Pot life is the shortest
time in an Epoxy's cure cycle because of exothermic reaction. Exotherming is where the epoxy's rate of cure is accelerated from
its own heat build-up from
being in a confined area such as the container or 'pot' it was mixed in. If the pot life
is reached and the batch is blown, it will be unusable and need to be discarded.
2) Open Time
Open time is how long
you have to do additional work or applications with or into the epoxy
after it has been applied such as release air, broadcast aggregate, etc.
This is a much longer time than Pot Life because generally the epoxy is
applied in a thin film over a large area allowing heat generated during
curing to dissipate and not accelerate the cure rate.
3) Cure time -
Initial
Initial cure time is
when the epoxy is no longer tacky and feels dry to the touch.
4) Cure Time -
Final
Final cure time is
when the epoxy reaches its solid state properties and curing is complete.
The following are our
standard Epoxy Products
We also offer Modified Versions and Custom Formulations.
All mix ratios are by volume.
-
FS-190 (mix ratio 2:1 / A:B)
Floor Sealer Epoxy is a high strength, water clear system for use
as a roller applied sealant in Industrial Flooring, Quartz Flooring,
Interior Riverstone Flooring and Broadcast Flooring applications. FS-190 is
extremely durable, chemical resistant and can be used as a commercial grade
Decoupage System or a Santex binder epoxy.
-
TC-200
(mix ratio 2:1 / A:B)
Top Coat Epoxy is a pigmented, high strength, high build
thixotropic industrial floor finish. It is extremely durable, chemical
resistant with excellent scratch and impact resistance. Applied by
brush/roller, squeegee or airless sprayer. Available in 14 standard colors
with custom colors available upon request. TC-200 can be used as a colored
Santex binder for troweled systems.
-
FP-80 (mix ratio 2:1 / A:B)
Floor Plate Epoxy is a clear self-leveling system for use in
Surface Plate applications. This system is extremely hard and
can be used in industrial laminating applications that have harsh or
punishing environments.
-
FP-85
(mix ratio 2:1 / A:B)
Floor Plate Epoxy that is the pigmented version of the FP Series
Epoxies for use in Surface Plate applications. Available in 14
standard colors with custom colors available upon request. Both Floor Plate
Epoxies are extremely durable, chemical resistant with excellent scratch and
impact resistance.
-
FP-90
(mix ratio 1:1 / A:B)
Floor Plate Epoxy that is designed for use in the Aerospace
Industry Test Bed applications. This 100% solids, zero VOC system has a very
slow rate of cure to achieve the most level and flat surface area possible.
The FP-90 provides a perfect surface that is unmatched and allows for the
floating of air bearing devices with little to no drift while using minimal
air pressure. Available in Black.
-
Stone Bond Epoxy Series is used as the binder epoxy for
troweled porous exterior Riverstone Decking applications. Stone Bond resins
(Part 'A') can be used with either the Summer Cure or Winter
Cure Stone Bond hardeners (Part 'B'). Stone Bond epoxy resins are
designed to maintain the correct troweling viscosity at the given
application temperature. Stone Bond hardeners are designed to give a desired
rate of cure at the application temperature. Stone Bond is also suitable for
exterior Industrial Flooring and Quartz Flooring applications exposed to
direct sunlight. Stone Bond can also be used in special application
variations as the binder of choice for Santex Flooring, Patching or
Substrate Modifying Systems. Stone Bond Epoxies will cure out clear in the
presence of moisture.
-
SB-30 (mix ratio 2:1 / A:B)
Stone Bond Epoxy with suggested application temperature of 20 to
40 degrees F.
-
SB-40 (mix ratio 2:1 / A:B)
Stone Bond Epoxy with suggested application temperature of 35 to 50
degrees F.
-
SB-50 (mix ratio 2:1 / A:B)
Stone Bond Epoxy with suggested application temperature of 40 to
65 degrees F.
-
SB-60 (mix ratio 2:1 / A:B)
Stone Bond Epoxy with suggested application temperature of 60 to
80 degrees F.
-
SB-65 (mix ratio 2:1 / A:B)
Stone Bond Epoxy with suggested application temperature of 75 to
95 degrees F.
-
SB-95 (mix ratio 2:1 / A:B)
Stone Bond Epoxy with suggested application temperature of 90 to
115 degrees F.
-
DS-190 (mix ratio 2:1 / A:B)
Deck Sealer Epoxy is a sealant for exterior Epoxy Riverstone
Decking applications that have aged due to UV degradation from exposure to
direct sunlight and/or excessive foot traffic. DS-190 restores the
high gloss beauty of the original decking along with maintaining the decks
structural integrity. Being a fluid system, it is easily applied by brush
and roller or airless sprayer after deck has been pressure washed and
allowed to dry. This system has all the advantages of the Stone Bond
Epoxies.
-
Smooth Webbing Epoxy Series is used for the lamination of
the normally porous Riverstone Decking overlays to achieve a non-porous Riverstone
Flooring for indoor use and to satisfy local health department regulations.
The SW Series Epoxies are selected according to their vertical hold range
differences that are needed to properly laminate small, medium or large
stone installations at a given application temperature. All the SW Epoxies
are available with Summer Cure or Winter Cure hardeners.
-
SW-10 (mix ratio 3:1 / A:B)
Smooth Webbing Epoxy for lamination of smaller size stone (3/16
to 1/4 inch) overlays.
-
SW-20 (mix ratio 3:1 / A:B)
Smooth Webbing Epoxy for lamination of medium size stone (1/4 to
1/2 inch) overlays.
-
SW-30 (mix ratio 3:1 / A:B)
Smooth Webbing Epoxy for lamination of larger size stone (3/8 to
3/4 inch) overlays. Also used with small or medium stone formed vertical
applications such as step risers, wall base, cantilever pool copings, etc.
-
DECO
(mix ratio 1:1 / A:B)
Decoupage Epoxy is a clear self-leveling system designed for
laminating bar tops, table or counter tops, pictures, art work, clocks,
cypress, etc. This system offers a slow rate of cure making it ideal for the
novice user or for tedious application environments where more time is helpful.
-
IG-100
(mix ratio 1:1 / A:B)
Injection Grout Epoxy is a flexible, extremely fluid system with
a very slow rate of cure for use as a penetrating primer for most of our
flooring and decking systems. IG-100 is also used with injection equipment
for concrete vertical or horizontal crack repair where motion or thermal
shock is anticipated.
-
IG-3
(mix ratio 2:1 / A:B)
Injection Grout Epoxy is a high strength, extremely fluid system
with a rapid rate of cure for use with injection equipment for concrete
vertical or horizontal crack repair. IG-3 has excellent resistance to
moisture and chemical environments making it an excellent binder for Santex
or Slurry coat applications.
-
FL-115
(mix ratio 1:1 / A:B)
Flexible Laminating Epoxy is used in conjunction with our special
fiberglass cloth tape for preparation of cracks, seams, cold joints or
expansion joints in substrate. This process eliminates or helps reduce the
risks of these points of movement in substrate from telegraphing back
through what ever decorative over-lay is finally applied to substrate.
FL-115 also produces a flexible, self-leveling, waterproofing membrane in
poured applications.
-
VP-110 (mix ratio 1:1 / A:B)
Vertical Primer Epoxy is a non-sagging thixotropic paste for use
as a vertical primer on areas receiving troweled overlays such as cove base
installations. This system has good tensile elongation to absorb thermal
movement, extended open time for tedious applications and can be applied by
brush or roller.
-
Structural Gel Epoxy Series
is a rigid high strength system
used in vertical or filler applications and for structural bonding of
similar or dissimilar materials. This system is used as the matrix membrane
for vertical exposed aggregate wall systems or as a primer for formed
vertical Riverstone Decking installations such as pool copings and step
risers. Suitable for crack sealing in conjunction with injection grouting
where a rigid system is desired. The SG Series epoxies are selected to suit
the application environment and temperature. Both components of these
systems are gel consistency which makes measuring and mixing extremely easy
and error free.
-
SG-22 (mix ratio 1:1 / A:B)
Structural Gel Epoxy - 22 has the fastest rate of cure and lowest
viscosity for use in cold weather environments.
-
SG-23 (mix ratio 2:1 / A:B)
Structural Gel Epoxy - 23 has an accelerated rate of cure and medium
viscosity for use in cool weather environments.
-
SG-25 (mix ratio 1:1 / A:B)
Structural Gel Epoxy - 25 is the most used of the SG Series with a
slow rate of cure and normal gel viscosity for use in average weather
environments.
-
SG-25 T (mix ratio 1:1 / A:B)
Structural Gel Epoxy - 25 T is a thicker version of the SG-25 system for
use at higher application temperatures and for use with larger aggregate in
vertical exposed aggregate installations.
-
SG-27 (mix ratio 2:1 / A:B)
Structural Gel Epoxy - 27 has the slowest rate of cure for use in hot
weather environments or tedious applications where more open time would be
useful.
-
Flexible Gel Epoxy Series is a high elongation,
non-sagging system that produces a waterproofing membrane for expansion
joints, cracks, seams and cold joints. Suitable for crack sealing in
conjunction with injection grouting where movement or expansion and
contraction are present. Creates a flexible mortar mix when blended with an
equal volume of sand.
-
FG-100 (mix ratio 1:1 / A:B)
Flexible Gel Epoxy with an elongation factor of 100% and a higher
heat distortion factor than the FG-125. The FG-100 system is also available
in both the summer cure and winter cure versions widening its application
temperature range. This system would be used in applications exposed to the
elements.
-
FG-125 (mix ratio 1:1 / A:B)
Flexible Gel Epoxy with an elongation factor of 125% and a lower
heat distortion factor than the FG-100. The FG-125 system is designed for
substrate preparation and waterproofing applications that will be covered
with decorative overlays.
-
CC-32
(mix ratio 1:1 / A:B)
Cold Cure Epoxy is a high strength clear system for use as a
flooring sealant at extremely cold application temperatures. Suitable as a
Santex binder and Slurry Coat epoxy, this system has outstanding durability
and chemical resistance.
-
D50-50
(mix ratio 2:1 / A:B)
Cold Cure Epoxy is a high strength clear system for use at
extremely cold application temperatures. This system was originally
formulated to satisfy the need to do concrete repair work in a large freezer
food storage warehouse that maintained a temperature of -20 degrees F. This
system has a very short pot life and open time and must be used and mixed in
colder environments.
-
TS-65 (mix ratio 2:1 / A:B)
Tank Sealer Epoxy is a fluid thixotropic system for flood coating
or roller coating horizontal areas to create a waterproofing membrane in
storage tanks or containment areas made of concrete, steel, fiberglass or
aluminum. TS-65 has a high bond strength, is very durable and chemically
resistant. Available in Summer Cure and Winter Cure versions.
-
TS-75 (mix ratio 2:1 / A:B)
Tank Sealer Epoxy is a non-sagging paste system for roller
coating vertical and overhead areas to create a waterproofing membrane in
storage tanks or containment areas made of concrete, steel, fiberglass or
aluminum. TS-75 has a high bond strength, is very durable and chemically
resistant. Available in Summer Cure and Winter Cure versions.
-
TS-75 P (mix ratio 2:1 / A:B)
Tank Sealer Epoxy that is the same as TS-75 except for being
pigmented, generally white, to give second coat applications a different
appearance to eliminate applicator error such as holidays in the
waterproofing membrane being applied.
-
Rigid Casting Epoxy Series
is a fluid system used for
structural bonding, laminating, art casting, electronics potting, etc. The
RC Series epoxies are selected to suit
the application environment and temperature. They are available in thick or
thin viscosity versions to suit a wide range of applications and rates of
cure. These systems are non-conductive, high strength, high heat distortion,
self-leveling epoxies and are available in clear or pigmented versions.
-
RC-52 (mix ratio 1:1 / A:B)
Rigid Casting Epoxy - 52 is the 'Fast Cure' of the series for
specialized applications. This system has a pot life of ten minutes and
reaches handling strength in one hour at 77 degrees F.
-
RC-53 (mix ratio 2:1 / A:B)
Rigid Casting Epoxy - 53 is for use in applications requiring a rapid
cure or for use at lower application temperatures. This system has high
strength properties without being brittle, making it ideal for specialized
casting.
-
RC-55 (mix ratio 1:1 / A:B)
Rigid Casting Epoxy - 55 is the most widely used of the RC series. The 45
minute pot life at 75 degrees F seems to make it suitable for a wide range
of applications.
-
RC-57 (mix ratio 2:1 / A:B)
Rigid Casting Epoxy - 57 has the slowest rate of cure for use
at higher application temperatures or tedious applications where more open time would be
useful.
-
RC-190 (mix ratio 2:1 / A:B)
Rigid Casting Epoxy - 190 is a special 'Armor Plating'
formulation to satisfy special needs of the electronics potting industry.
This system is extremely hard and durable making it virtually impossible to
be broken down to reveal circuitry within the casting. Available in a thick
black color to further hide contents within the casting.
-
Deep Casting Epoxy Series
parallel the Rigid Casting
Series Epoxies. The DC Series epoxies contain a filler to eliminate
'Boiling' in large deep (3/4" plus) pours and are selected to suit
the application environment and temperature. They are available in thick or
thin viscosity versions to suit a wide range of applications and rates of
cure. These systems are non-conductive, high strength, high heat distortion,
self-leveling epoxies and are available in opaque or pigmented versions.
-
DC-52 (mix ratio 1:1 / A:B)
Deep Casting Epoxy - 52 is the 'Fast Cure' of the series for
specialized applications. This system has a pot life of ten minutes and
reaches handling strength in one hour at 77 degrees F.
-
DC-53 (mix ratio 2:1 / A:B)
Deep Casting Epoxy - 53 is for use in applications requiring a rapid
cure or for use at lower application temperatures. This system has high
strength properties without being brittle making it ideal for specialized
casting.
-
DC-55 (mix ratio 1:1 / A:B)
Deep Casting Epoxy - 55 is the most widely used of the DC series. The 45
minute pot life at 75 degrees F seems to make it suitable for a wide range
of applications.
-
DC-57 (mix ratio 2:1 / A:B)
Deep Casting Epoxy - 57 has the slowest rate of cure for use
at higher application temperatures or tedious applications where more open time would be
useful.
-
Santex
is a sand filled epoxy system for use as a
troweled industrial floor base or topping for leveling or sloping, a
concrete patch or repair mortar for spall repair. Santex can be configured
with different epoxy binders to achieve varied solid state properties to
suit a variety of application needs. Sand and/or aggregate sizes and
blends can be varied to application needs and to fit the troweling circumstances.
The general aggregate to epoxy ratio is 9 to 1.
-
Slurry Coat
is a sand filled epoxy system that has a
soupy consistency that can be applied by trowel, squeegee or gauge rake.
This is used to fill uneven, rough or spalling substrates by giving the
self-leveling epoxy more volume as the aggregate filler settles into lower
areas. Slurry Coat can be configured with different epoxies to achieve a
variety of solid state properties to suit many application needs. The
general aggregate to epoxy ratio is 2 to 1.
Consult Product's
Technical Bulletin for additional information.
A specific epoxy formulation
should be chosen to satisfy your application requirements such as liquid and
solid state properties, pot life, open time, cure time, exposure, etc.
A particular epoxy product may have many proper applications throughout many
industries; therefore, a clear understanding of epoxies, their applications and
limitations will aid in proper product selection and use. An Epoxy's solid state
properties can only be achieved by thorough mixing of Parts 'A' and 'B' at the
proper mix ratio. Higher application temperatures will accelerate reaction time
reducing pot life, open time and cure time while making the viscosity of the
product thinner. Lower application temperatures will make reaction time sluggish
extending pot life, open time and cure time while increasing the viscosity of
the product.
Every reasonable precaution
is taken in the manufacture of all products and compiling of data to assure that
they comply with ROCK ART'S exacting standards. Reliable tests and field
experience of these products indicate there utility as described herein. The suitability of a product for
an intended use shall be solely up to and the ultimate responsibility of the
user/purchaser of that product. You must determine your reliability as an
applicator for your specific application. We are not responsible if a product should be
used by the user/purchaser in a manner to infringe any patent held by others.
We assume no liability for
damages of any kind and no guarantee of results is given using these products or data
because every possible variation in the method of their use or
conditions under which they are applied cannot be anticipated.
User accepts product "AS
IS" and without warranties, expressed or implied.
|
